logo-APP_ver
✕
  • Home
  • About us
  • Services
    • Cathodic dip coating (KTL)
    • Robotic welding
    • Special applications
    • Complete parts production
  • Quality
  • Blog
  • Contact
  • EN
    • CZ
    • DE

We are a member of Colegium holding

 +420 605 009 909

info@appcz.eu

Kariéra
  • EN
    • CZ
    • DE
logo-APP_ver
  • Home
  • About us
  • Services
    • Cathodic dip coating (KTL)
    • Robotic welding
    • Special applications
    • Complete parts production
  • Quality
  • Blog
  • Contact
  • EN
    • CZ
    • DE
logo-APP_ver
  • Home
  • About us
  • Services
    • Cathodic dip coating (KTL)
    • Robotic welding
    • Special applications
    • Complete parts production
  • Quality
  • Blog
  • Contact
  • EN
    • CZ
    • DE

How to Prevent Surface Defects in Cathodic Dip Coating

16. September 2026

Cathodic dip coating is one of the most important processes for protecting metal components against corrosion. However, the quality of the resulting coating depends not only on the parameters of the cathodic dip coating process itself, but also on the stability of the entire process chain – from chemical pretreatment and bath parameter control through to final inspection. Even a minor deviation can lead to surface defects that adversely affect service life and compliance with stringent OEM standards. What are the most common coating defects, how can their root causes be identified, and what other problems can occur?

Pores and Craters Caused by Electrical Breakdown

One of the most common defects is pores and craters, which form as a result of electrical breakdown during e-coat deposition. These can be caused by excessive bath voltage, as well as surface contamination with silicones or residues of welding and sealing materials containing silicates or silicones. These microscopic defects compromise the integrity of the protective film and can become initiation points for subsequent corrosion.

Water Bubbles and Blistering Caused by Inadequate Rinsing

Another problem is water bubbles and blisters, which indicate moisture trapped beneath the coating film. The most common causes are inadequate rinsing after pretreatment, high conductivity of demineralised water or poor drainage in the enclosed cavities of complex components. Moisture trapped beneath the coating can subsequently cause blistering during corrosion or climatic testing, or under operating loads.

Insufficient Coverage in Shielded Areas and the Faraday Cage Effect in E-Coating

An important parameter of cathodic dip coating quality is coverage inside profiles, cavities and complex-shaped components. Insufficient coating film thickness is often associated with a weak Faraday effect, an incorrectly configured electrical contact system for the component, insufficient throwing power or suboptimal anode geometry. The result is uneven film thickness, which reduces corrosion resistance, particularly in hard-to-reach areas of the structure.

A Faraday cage is a physical phenomenon in which electric charge is concentrated on the outer surface of a conductor. As a result, the electric field inside an enclosed hollow conductive body is zero. One of the best-known practical examples is a car struck by lightning. The electric charge is distributed across the conductive bodywork, while the interior and its occupants remain protected. This is why travelling in a car during a thunderstorm is generally safe.

In cathodic dip coating, however, the Faraday cage effect makes the process more difficult because the electric field plays a crucial role. The metal component is immersed in a paint bath and connected as the cathode. The applied voltage causes the paint particles to move and deposit on the component’s surface. This is straightforward on external surfaces, but deep profiles and cavities are subject to what is known as shielding. The electric field does not penetrate these areas with the same intensity, making it more difficult for paint particles to reach the internal surfaces.

Importance of Proper Electrical Contact During Coating

The ability of the coating to penetrate cavities and other hard-to-reach areas is known as throwing power. The higher the throwing power, the deeper the coating can penetrate. The Faraday cage effect limits this ability. To prevent complex-shaped components from having areas with insufficient coating coverage or no coating at all, process modifications are necessary.

One way to overcome shielding is through carefully planned anode positioning. For complex components, we therefore use auxiliary or rod anodes, which are inserted directly into critical areas. This brings the electric field closer to surfaces that would otherwise remain shielded, allowing paint particles to form a protective coating on them more reliably.

However, the geometry of the individual component is decisive, as the electric field behaves differently in an open profile than in a deep cavity with a narrow opening. The key is therefore to adapt the anode arrangement to the geometry of the specific component being coated.

Simply Increasing the Voltage Is Not Enough

The throwing power of an e-coat is not determined solely by anode positioning. The chemical properties of the bath, its conductivity and temperature are also important.

Another aspect of electrophoretic coating is the use of voltage ramps. Rather than immediately applying the full voltage to the bath, voltage ramps allow it to be increased gradually. This enables us to control how the coating forms on the component and improve paint penetration into less accessible areas. By combining these factors appropriately, the specified coating thickness can be achieved not only on external surfaces but also inside profiles and cavities.

Measuring coating thickness on visible surfaces is straightforward. Inside an enclosed profile, however, the situation is more complicated. We also verify that the required coating thickness has been achieved in these areas. For measurement, we use a magnetic probe. When placed against the surface, it determines the distance to the metal substrate from changes in the magnetic field, thereby measuring the thickness of the coating.

In areas that cannot be reached with the probe, such as deep inside an enclosed profile, we perform destructive sectioning on selected test components. The component is cut open, and the coating thickness is measured directly on the cross-section.

Underfilm Corrosion Begins During Pretreatment

Another serious defect is underfilm corrosion, which often originates not in the coating process itself, but during chemical pretreatment. Poor-quality zinc phosphating, unstable pH or an inadequately formed conversion coating can weaken coating adhesion to the component. During salt spray corrosion testing, this may become apparent through coating delamination and corrosion spreading beneath the coating.

Effectively eliminating these defects requires systematic diagnostics and continuous monitoring of process parameters. At Automotive Painting Partners, we therefore use a combination of advanced diagnostic methods when analysing surface defects, enabling us to identify precisely where and why defects arise throughout the cathodic dip coating process.

Our analyses include coating thickness measurements, microscopic analysis, monitoring of rinse water conductivity and 3D scanning of critical areas. These methods enable us to quickly identify whether a defect originates in chemical pretreatment, electrophoretic deposition parameters or the design geometry of the component being coated, and to propose process measures that allow immediate adjustment of parameters directly on our e-coat lines.

Defect Analysis as Part of Quality Management

Our aim is not only to identify defects that have occurred, but above all to prevent them from recurring. Thorough root cause analysis helps optimise process settings, reduce rejection rates and improve long-term production stability. This enables our customers to consistently maintain stable cathodic dip coating quality and meet the demanding requirements of OEM manufacturers as well as the assessment criteria of VDA audits.

Would you like to improve the stability of your cathodic dip coating process and reduce surface defects? Contact Automotive Painting Partners. We will help you optimise your process to ensure it consistently meets the requirements of automotive manufacturing.

Related posts

29. October 2026

E-Coat for Electric Vehicles: How to Protect Underbody Components Around the Battery


Read more
21. October 2026

From Prototype to Millions of Parts: How to Ensure Consistent E-Coat Quality


Read more
15. October 2026

Stanislava Novotná: We Want to Combine APP’s Flexibility with Even Greater Efficiency and Stability


Read more

Contact

Are you looking for a reliable solution? Contact us!

info@appcz.eu

Please enable JavaScript in your browser to complete this form.


Agreement *

Loading

Company headquarters

Automotive Painting Partners s.r.o.
Chobotecká 365, Čejetice
293 01 Mladá Boleslav

ID: 28546954
VAT: CZ28546954

The company is registered at the Court in Prague C 149405

Offices

Pražská 2589
288 02 Nymburk

17. listopadu 60
549 54 Police nad Metují

Nymburská 53
289 13 Zvěřínek-Písty

Quick contact

+420 737 101 815

 info@appcz.eu

Useful links

Certification
General Terms and Conditions of Purchase
Quality Policy
Social Responsibility
Energy Management Policy
EnMS Objectives

Links

Cookies
GDPR

  

© 2026 website created by SEMTIX.cz
    Manage Consent
    To provide the best possible service, we use technologies such as cookies to store and/or access information about your device. Consent to these technologies will allow us to process data such as browsing behavior or unique IDs on this website. Refusal or withdrawal of consent may adversely affect certain features and functionality.
    Functional Always active
    Technical storage or access is strictly necessary for the legitimate purpose of enabling the use of a specific service that the subscriber or user has explicitly requested, or solely for the purpose of carrying out the transmission of a message via an electronic communications network.
    Preferences
    Technical storage or access is necessary for the legitimate purpose of storing preferences that are not requested by the subscriber or user.
    Statistics
    A technical storage or access that is used exclusively for statistical purposes. Technical storage or access that is used solely for anonymous statistical purposes. Without a subpoena, voluntary compliance by your Internet Service Provider, or other records from a third party, information stored or obtained solely for this purpose cannot usually be used to identify you.
    Marketing
    Technical storage or access is required to create user profiles for the purpose of sending advertising or to track the user across a website or across several websites for similar marketing purposes.
    • Manage options
    • Manage services
    • Manage {vendor_count} vendors
    • Read more about these purposes
    Show preferences
    • {title}
    • {title}
    • {title}